**3D Metallic Plaster Art Tutorial | DIY Plaster Art Tutorial for Beginners — Transcript & Summary | SozAI**
Source: https://sozai.app/transcript/3d-metallic-plaster-art-tutorial-diy-beginners/

TheZenDoc Studio shares a complete DIY tutorial for making 3D metallic plaster wall art in the color Putor, from wire mesh framing to plaster, sanding, primer, and paint.

## Key Takeaways

- Oversized wire mesh and plaster bandages create a sturdy, flexible base for 3D plaster sculptures.
- Building up multiple thin layers of joint compound and sanding between stages yields a smooth finish.
- Priming before painting and applying several coats of Putor acrylic produces a metallic look.

## What the video covers

- The creator uses a brass letter wall art piece as the base frame for the sculpture.
- Flexible wire mesh is cut oversized (about double the frame size) and trimmed afterward.
- Wire mesh is attached to the metal frame with hot glue, with open edges sealed with hard glue.
- Gloves are recommended when handling wire mesh because it is sharp.
- Plaster bandages are wetted and smoothed over the wire to add structural integrity and serve as a base layer.
- Joint compound or texture paste is applied in several layers over one to two weeks, with a day or two of drying between layers.
- After drying, the surface is sanded smooth, and extra texture paste may be added where needed.
- A household primer (or acrylic paint as a substitute) is applied before painting.
- Amsterdam acrylic paint in the color Putor, a metallic grayish tone with beige undertones, is applied in about four coats with spot touch-ups, then left to dry about three days.
- The creator shares the finished piece and encourages viewers to subscribe and check the description for links.

## Chapters

1. 00:00 Introduction
2. 01:00 Project overview and channel welcome
3. 02:09 Choosing the brass letter wall art base
4. 04:54 Cutting and attaching the wire mesh
5. 07:22 Shaping the sculpture and sealing edges
6. 09:58 Applying plaster bandages
7. 11:39 Applying joint compound layers
8. 12:53 Sanding, priming, and painting

Answers

## Questions about this video

What base material does the creator use for this wall art?

The creator uses a brass letter wall art piece as the metal frame base. It was in perfect condition, so they found it well suited to the project.

How much wire mesh should you cut?

The creator recommends cutting about double the size of the canvas or frame you are working with. Any excess can be trimmed off after attaching it.

How long does the paint need to dry before the piece is finished?

After applying the Putor acrylic in about four coats with spot touch-ups, the creator waited about three days for the paint to dry before proceeding.

## Full Transcript — Download SRT & Markdown

00:00

Speaker A

what's up YouTube, it's B from the Zendo here. I hope everyone is doing well today. It's good to see you.

00:42

Speaker A

you see next to me it is in the color putor and I have to say that for my metallic Series in collection I have been experimenting a lot with different kinds of metallic paints and I have to say that this one is one that I Tru

01:00

Speaker A

So in today's video, I'll be sharing the complete tutorial and the behind-the-scenes process for how I made this 3D plastic wall art that you see next to me. It is in the color Putor, and I have to say that for my metallic series in my collection, I have been experimenting a lot with different kinds of metallic paints. I have to say that this one is one that I truly enjoyed working with. I love the outcome. I enjoyed the process.

01:18

Speaker A

support my channel as I currently have been working on putting out a ton of valuable information sharing my journey documenting my process with you sharing pretty much all of my knowledge with you so I truly would appreciate if you would

01:34

Speaker A

Before we get into the process, if you're new here, welcome to my channel. If you're not, welcome back. If you're not subscribed, I would truly, truly love for you to subscribe and support my channel, as I currently have been working on putting out a ton of valuable information, sharing my journey, documenting my process with you, sharing pretty much all of my knowledge with you. So I truly would appreciate it if you would just hit that subscribe button and turn on bell notifications as well, so that whenever I have new videos out, you're always the first to know. That way you're not missing out on any new information that I might have to share or what I have going on in the works.

01:48

Speaker A

or what I have going on in the works as well and if you're interested in seeing the behind the proces for this really really beautiful wall art let's get into it so I'm using this brass letter wall art

02:09

Speaker A

And if you're interested in seeing the behind-the-process for this really, really beautiful wall art, let's get into it.

02:25

Speaker A

I always say double the size of the canvas or whatever frame you working with should be fine and you can always trim off the excess [Music] [Music] next I am gluing the wire mesh to the metal frame with a hug glue gun on both

03:06

Speaker A

So I'm using this brass letter wall art that I found. It was in perfect condition, and I thought it'd be perfect for my work.

04:08

Speaker A

open edges with a hard GL G [Music] [Music] [Music] next I use a hul glue gun to glue the wire mesh to the metal frame in a way that allows it to hold the shape that I have in mind I should also mention here

04:54

Speaker A

Next, I am cutting my flexible wire mesh. I'm just cutting off a large size. If you're unsure of how much you need, I always say double the size of the canvas or whatever frame you're working with should be fine, and you can always trim off the excess.

05:42

Speaker A

and this is what the base frame for my sculpture is looking like after I have glued and trimmed off the excess wire I like it already [Music] next I apply a layer of plaster bandages to cover the wire and I do this by

06:06

Speaker A

Next, I am gluing the wire mesh to the metal frame with a hot glue gun on both ends.

06:36

Speaker A

serves as the base layer for which you then apply your joints compound paste in following steps [Music] once your wire mesh is completely covered and a layer of plastic bandages it is time to apply your joint compound or plaster

07:22

Speaker A

Next, I spent some time figuring out what shape I want for my sculpture.

07:41

Speaker A

when I am happy with how it's come along or where at any point I feel um there is no number of layers that you need to apply that's the point I'm trying to make [Music] once I'm happy with the layers that I've

08:17

Speaker A

Once I've mapped out my frame and determined that the wire mesh I have is sufficient, I proceed to seal off the open edges with a hard glue.

08:30

Speaker A

sanding and that's completely [Music] normal in this case I ended up going back in to work on the edges that I still wasn't happy with after sanding but I did that off camera [Music] [Music] when I am happy with the finish the next

09:12

Speaker A

Next, I use a hot glue gun to glue the wire mesh to the metal frame in a way that allows it to hold the shape that I have in mind. I should also mention here that when you're working with wire mesh, it is incredibly helpful to have gloves. I know I'm not one, but hear me out: wire mesh is really sharp and can easily hurt you, so it's helpful to have gloves.

09:42

Speaker A

I let the primer dry for about 2 to 3 hours and now I'm going in with my Amsterdam acrylic paint in the color putor [Music] putor is a metallic grayish color which is gray with beige undertones but it can

10:16

Speaker A

And this is what the base frame for my sculpture is looking like after I have glued and trimmed off the excess wire. I like it already.

10:33

Speaker A

this is what it looks like after applying just two coats of paint I ultimately ended up using about four coats and spot Tre in some areas just to get my desired [Music] look I waited about 3 days for the paint

10:59

Speaker A

Next, I apply a layer of plaster bandages to cover the wire. I do this by wetting the bandages with my brush and smoothing it over the wire. As the bandages dry, they harden and allow my frame to have a little bit more structural integrity. Since the wire mesh I use is very flexible, it also serves as the base layer on which you then apply your joint compound paste in following steps.

11:17

Speaker A

[Music] longevity and this is the final look I honestly I am in awe of it I am absolutely speechless Le I am stunned I completely am gup smacked I love it I love how it came out the color is so

11:39

Speaker A

Once your wire mesh is completely covered in a layer of plaster bandages, it is time to apply your joint compound or plaster mixture. I tend to apply several layers of my joint compound or texture paste over the course of one to two weeks, allowing for about a day or two in between for the layers to dry. I stop when I am happy with how it's come along, or where at any point I feel there is no number of layers that you need to apply. That's the point I'm trying to make.

11:54

Speaker A

you guys think about this color [Music] [Music] so yeah that was the entire process I hope that it was insightful informative and engaging for you as a reminder all of the links will be left in the description box if you're interested in

12:53

Speaker A

Once I'm happy with the layers that I've applied, I give it about a day or two to fully dry, and then I go in with the sanding paper to sand out all of the roughness. Sometimes you might need to go back in with more texture paste after sanding, and that's completely normal. In this case, I ended up going back in to work on the edges that I still wasn't happy with after sanding, but I did that off camera.

13:05

Speaker A

website or my Etsy all of the links will be in the description box as well on my part I have truly enjoyed putting this video together it's been fun hanging out with you and I will see you all in my

13:18

Speaker A

When I am happy with the finish, the next step is to apply a layer of household primer to prime the work for painting. If you don't have primer on hand, you can also just apply a layer of acrylic paint, and it should have the same effect.

Topics: plaster art DIY wall art 3D plaster sculpture metallic paint wire mesh joint compound Putor paint Amsterdam acrylic tutorial beginner art

Study this video

- [Flashcards from this video](https://sozai.app/tools/ai-flashcard-generator/?from=transcript&id=86215)
- [Quiz on this video](https://sozai.app/tools/quiz-generator/?from=transcript&id=86215)

Free, made by AI from this transcript. No signup.


---
This is the markdown twin of https://sozai.app/transcript/3d-metallic-plaster-art-tutorial-diy-beginners/ — the same content, without the markup.
Published by SozAI (https://sozai.app). Reuse and quotation are allowed with attribution and a link back.
Machine-readable index: https://sozai.app/llms.txt · data API: https://sozai.app/api/